| TIPS NO: 193 |
| Revision: B |
| June 2000 |
KODAK
Vision Polycarbonate Aspheric Single Vision Lens
Product Specifications
Part No: K587-945
Purpose:
The following information is provided as product specifications
and processing guidelines for, Kodak Polycarbonate aspheric single vision,
semi-finished lens. If you have any processing questions, contact our Technical
Services department at 1(800)759-4630.
Summary of revision:
This TIPS revision changes the product name and adjusts the true curve
values for the 3.75, 4.50, 6.25, 7.25, and 7.50 base curves.
Lens Specifications
Single Vision: (Semi-Finished)
Blank Size: 75 mm diameter
Power range: -13.00 to +8.00
Base Curves: 0.50, 1.00, 2.50, 3.75, 4.50, 4.75, 5.25, 5.50, 6.25, 7.25, 7.50, 8.00
| Characteristics | Kodak Polycarbonate Lenses |
| Refractive Index | 1.586 |
| Dispersion Value (Abbe) | 28.0 |
| Density | 1.20 |
| UV Transmission Cutoff | 380nm |
| Rear Surface Coating | Required |
| Chemical Resistance | Poor |
| Nominal Base Curve | Actual Base Curve |
Radius
mm |
Sphere Sag 50mm |
Concave Curve
|
Edge Thickness
|
Center
Thickness |
|||
|
0.50 |
0.60 |
883.332 |
0.35 |
6.00 |
17.02 |
9.25 |
|||
|
1.00 |
1.03 |
514.562 |
0.61 |
6.00 |
16.46 |
9.50 |
|||
|
2.50 |
2.55 |
207.843 |
1.51 |
6.00 |
14.62 |
9.46 |
|||
|
3.75 |
3.79 |
139.842 |
2.25 |
6.00 |
13.33 |
9.77 |
|||
|
4.50 |
4.46 |
118.834 |
2.66 |
6.00 |
10.00 |
7.22 |
|||
|
4.75 |
4.75 |
111.579 |
2.84 |
6.00 |
10.00 |
7.62 |
|||
|
5.25 |
5.13 |
103.314 |
3.07 |
6.00 |
10.00 |
8.00 |
|||
|
5.50 |
5.49 |
96.539 |
3.29 |
6.00 |
10.00 |
8.42 |
|||
|
6.25 |
6.27 |
84.530 |
3.78 |
6.00 |
10.00 |
9.57 |
|||
|
7.25 |
7.07 |
74.965 |
4.29 |
6.00 |
10.00 |
10.74 |
|||
|
7.50 |
7.61 |
69.645 |
4.64 |
6.00 |
10.00 |
11.15 |
|||
|
8.00 |
7.95 |
66.667 |
4.87 |
6.00 |
10.00 |
12.09 |
|||
Kodak is a Trademark of Eastman Kodak Company, used under license by Signet Armorlite, Inc.
General:
Processing of the Kodak Polycarbonate
aspheric lens is similar to that of standard resin with a few exceptions.
We recommend using the following:
Computer Calculation of Rx:
The easiest, most efficient method to calculate and process values
for an Rx is to use an existing software package that contains the Kodak
Polycarbonate aspheric lens design data. If your software vendor has not included this
data in your system, Signet Armorlite's Technical Services will be happy to provide them
with that information.
Lens Layout:
The Kodak Polycarbonate aspheric lens is an aspheric
designed product. Therefore, a sag gauge for Rx calculation purposes should
not be used. Please use our published curve and surface contour data for all calculations.
These lenses are marked with both a semi-visible "K" and visible ink markings
for processing verification and fitting.
Surfacing should be done in reference to the dot located 2mm below the fitting cross on the 0-180·ƒ axis. Use the fitting cross for edging layout.
Prescribed prism by the doctor can be included. However, prism ground for cutout should never exceed 2mm.
Post-surface Coatings:
A backside scratch resistant coating is required on all
polycarbonate semi-finished lenses. Ensure that the pre-coat cleaning process removes all
dust and dirt particles. Clean with alcohol, acetone or methylene chloride will damage the
lens.
Tinting:
Polycarbonate material will not absorb tint. Therefore, in order to
tint, a tintable backside coating must be applied. Conventional hard resin tints are
acceptable. Neutralize by dipping the lens in a non-citrus liquid detergent and water.
Standard neutralizers will damage the lens.
AR Coatings:
Be sure factory ink marks are completely removed as
insufficient cleaning may cause ink markings to show through the Anti-Reflection coating.
Impact resistance is reduced when any lens is Anti-Reflection coated. Certain combinations
of lens thickness, backside scratch resistance coating, and Anti-Reflection coating have
shown to reduce impact resistance below FDA requirements. However, in our testing, the Kodak
Polycarbonate aspheric lenses with 1.0mm minimum center thickness or higher, have shown to
exceed the FDA requirements.
Impact resistance:
Testing is performed for impact resistance of the Kodak
Polycarbonate aspheric lens at 1.0mm center thickness. Kodak lenses can be
processed to meet applicable impact resistance requirements of FDA Regulations
21CFR801.410 and ANSI Z80.1. Conformance to this standard is the responsibility of all
subsequent processors. Impact resistant lenses are not unbreakable. Damaged lenses should
be replaced immediately.
| KODAK VISION 4159 POLYCARBONATE ASPHERIC LENS - SINGLE VISION | ||||||||||||||||||||||||||||||||||||||||||||
| MINUS ASPHERIC BASE CURVE SELECTION | PLUS ASPHERIC BASE CURVE SELECTION | |||||||||||||||||||||||||||||||||||||||||||
| Cylinder | Cylinder | |||||||||||||||||||||||||||||||||||||||||||
| Sphere Power | 0.00 | -0.25 | -0.50 | -0.75 | -1.00 | -1.25 | -1.50 | -1.75 | -2.00 | -2.25 | -2.50 | -2.75 | -3.00 | -3.25 | -3.50 | -3.75 | -4.00 | -4.25 | -4.50 | -4.75 | -5.00 | Sphere Power | 0.00 | -0.25 | -0.50 | -0.75 | -1.00 | -1.25 | -1.50 | -1.75 | -2.00 | -2.25 | -2.50 | -2.75 | -3.00 | -3.25 | -3.50 | -3.75 | -4.00 | -4.25 | -4.50 | -4.75 | -5.00 | |
| 0.00 | 9.00 | |||||||||||||||||||||||||||||||||||||||||||
| -0.25 | 8.75 | |||||||||||||||||||||||||||||||||||||||||||
| -0.50 | 8.50 | |||||||||||||||||||||||||||||||||||||||||||
| -0.75 | 3.75 Base | 8.25 | ||||||||||||||||||||||||||||||||||||||||||
| -1.00 | 8.00 | |||||||||||||||||||||||||||||||||||||||||||
| -1.25 | 7.75 | 8.00 Base | ||||||||||||||||||||||||||||||||||||||||||
| -1.50 | 7.50 | |||||||||||||||||||||||||||||||||||||||||||
| -1.75 | 7.25 | |||||||||||||||||||||||||||||||||||||||||||
| -2.00 | 7.00 | |||||||||||||||||||||||||||||||||||||||||||
| -2.25 | 6.75 | |||||||||||||||||||||||||||||||||||||||||||
| -2.50 | 6.50 | 7.50 Base | ||||||||||||||||||||||||||||||||||||||||||
| -2.75 | 6.25 | |||||||||||||||||||||||||||||||||||||||||||
| -3.00 | 6.00 | |||||||||||||||||||||||||||||||||||||||||||
| -3.25 | 2.50 Base | 5.75 | 7.25 Base | |||||||||||||||||||||||||||||||||||||||||
| -3.50 | 5.50 | |||||||||||||||||||||||||||||||||||||||||||
| -3.75 | 5.25 | |||||||||||||||||||||||||||||||||||||||||||
| -4.00 | 5.00 | 6.25 Base | ||||||||||||||||||||||||||||||||||||||||||
| -4.25 | 4.75 | |||||||||||||||||||||||||||||||||||||||||||
| -4.50 | 4.50 | |||||||||||||||||||||||||||||||||||||||||||
| -4.75 | 4.25 | |||||||||||||||||||||||||||||||||||||||||||
| -5.00 | 4.00 | 5.50 Base | ||||||||||||||||||||||||||||||||||||||||||
| -5.25 | 3.75 | |||||||||||||||||||||||||||||||||||||||||||
| -5.50 | 3.50 | |||||||||||||||||||||||||||||||||||||||||||
| -5.75 | 3.25 | |||||||||||||||||||||||||||||||||||||||||||
| -6.00 | 3.00 | 5.25 Base | ||||||||||||||||||||||||||||||||||||||||||
| -6.25 | 1.00 Base | 2.75 | ||||||||||||||||||||||||||||||||||||||||||
| -6.50 | 2.50 | |||||||||||||||||||||||||||||||||||||||||||
| -6.75 | 2.25 | |||||||||||||||||||||||||||||||||||||||||||
| -7.00 | 2.00 | 4.75 Base | ||||||||||||||||||||||||||||||||||||||||||
| -7.25 | 1.75 | |||||||||||||||||||||||||||||||||||||||||||
| -7.50 | 1.50 | |||||||||||||||||||||||||||||||||||||||||||
| -7.75 | 1.25 | |||||||||||||||||||||||||||||||||||||||||||
| -8.00 | 1.00 | |||||||||||||||||||||||||||||||||||||||||||
| -8.25 | 0.75 | 4.50 Base | ||||||||||||||||||||||||||||||||||||||||||
| -8.50 | 0.50 | |||||||||||||||||||||||||||||||||||||||||||
| -8.75 | 0.25 | |||||||||||||||||||||||||||||||||||||||||||
| -9.00 | 0.00 | |||||||||||||||||||||||||||||||||||||||||||
| -9.25 | ||||||||||||||||||||||||||||||||||||||||||||
| -9.50 | ||||||||||||||||||||||||||||||||||||||||||||
| -9.75 | ||||||||||||||||||||||||||||||||||||||||||||
| -10.00 | ||||||||||||||||||||||||||||||||||||||||||||
| -10.25 | ||||||||||||||||||||||||||||||||||||||||||||
| -10.50 | 0.50 Base | |||||||||||||||||||||||||||||||||||||||||||
| -10.75 | ||||||||||||||||||||||||||||||||||||||||||||
| -11.00 | ||||||||||||||||||||||||||||||||||||||||||||
| -11.25 | ||||||||||||||||||||||||||||||||||||||||||||
| -11.50 | ||||||||||||||||||||||||||||||||||||||||||||
| -11.75 | ||||||||||||||||||||||||||||||||||||||||||||
| -12.00 | ||||||||||||||||||||||||||||||||||||||||||||
| -12.25 | ||||||||||||||||||||||||||||||||||||||||||||
| -12.50 | ||||||||||||||||||||||||||||||||||||||||||||
| -12.75 | ||||||||||||||||||||||||||||||||||||||||||||
| -13.00 | ||||||||||||||||||||||||||||||||||||||||||||